- 您现在的位置：买卖IC网 > Sheet目录370 > ZXLD1100H6TA (Diodes Inc)IC LED DRVR WHITE BCKLGT SC-70-6
LAST TIME BUY
Closest Alternative is AP5724FDCG-7
ZXLD1100
Inductor selection
The choice of inductor will depend on available board
space as well as required performance. Small value
inductors have the advantage of smaller physical size
and may offer lower series resistance and higher
saturation current compared to larger values. A
disadvantage of lower inductor values is that they result
in higher frequency switching, which in turn causes
reduced efficiency due to switch losses. Higher inductor
values can provide better performance at lower supply
voltages. However, if the inductance is too high, the
output power will be limited by the internal oscillator,
which will prevent the coil current from reaching its
peak value. This condition will arise whenever the ramp
time (I LX(peak) x L/V IN ) exceeds the nominal 5 s
maximum ‘on’ time limit for the LX output.
The graphs opposite show the ZXLD1100 performance
for given inductor values and different manufacturers.
Recommended inductor values for the ZXLD1100 are
in the range 6.8 H to 22 H. The inductor should be
mounted as close to the device as possible with low
resistance connections to the LX and VIN pins.
Suitable coils for use with the ZXLD1100 are shown in
the table below:
Part No.
L
( H)
DCR
( )
I SAT
(A)
Manufacturer
CMD4D11-100MC 10
0.457 0.5
Sumida
www.sumida.com
DO1608-103
10
0.16
1.1
Coilcraft
www.coilcraft.com
LQH31CN100
10
1.3
0.23
Murata
www.murata.com
LB2012Y100MR
10
0.5
0.1
Taiyo Yuden
www.t-yuden.com
Diode selection
The rectifier diode (D1) should be a fast low
capacitance schottky diode with low reverse leakage at
the working voltage. It should also have a peak current
rating above the peak coil current and a continuous
current rating higher than the maximum output load
current.
The table below gives some typical characteristics for
diodes that can be used with the ZXLD1100:
Layout considerations
PCB tracks should be kept as short as possible to
minimize ground bounce, and the ground pin of the
device should be soldered directly to the ground plane.
It is particularly important to mount the coil and the
input/output capacitors close to the device to minimize
parasitic resistance and inductance, which will
degrade efficiency. The FB pin is a high impedance
input so PCB track lengths to this should also be kept as
short as possible to reduce noise pickup. Excess
capacitance from the FB pin to ground should be
avoided.
Diode
ZHCS400
ZHCS500
V F @ 100mA (mV)
300
300
I FSM (mA)
1000
1000
Ic (mA)
400
500
I R at 30V ( A)
15
15
Package
SOD323
SOT23
ISSUE 4 - JULY 2004
SEMICONDUCTORS
10
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
ZXLD1101ET5TA
IC LED DRVR WHITE BCKLGT SOT23-5
ZXLD1320DCATC
IC LED DRVR WHITE BCKLGT 14-TDFN
ZXLD1321DCATC
IC LED DRVR WHITE BCKLGT 14-TDFN
ZXLD1322DCCTC
IC LED DRIVR WHITE BCKLGT 14-DFN
ZXLD1350ET5TA
IC LED DRIVR WHITE BCKLGT TSOT-5
ZXLD1352ET5TA
IC LED DRIVER HIGH BRIGHT TSOT-5
ZXLD1356DACTC
IC LED DRIVER WHITE BCKLGT 6-DFN
ZXLD1360ET5TA
IC LED DRIVR WHITE BCKLGT TSOT-5
相关代理商/技术参数
ZXLD1100H6TC
制造商:ZETEX 制造商全称:ZETEX 功能描述:ADJUSTABLE LED DRIVER WITH INTERNAL SWITCH AND OPEN CIRCUIT PROTECTION IN SC70-6
ZXLD1101
制造商:ZETEX 制造商全称:ZETEX 功能描述:ADJUSTABLE LED DRIVER WITH INTERNAL SWITCH IN TSOT23-5
ZXLD1101ET5
制造商:Diodes Incorporated 功能描述:LED DRIVER ADJUSTABLE SMD 1101 制造商:Diodes Incorporated 功能描述:LED DRIVER ADJUSTABLE, SMD, 1101
ZXLD1101ET5
制造商:Diodes Incorporated 功能描述:LED DRIVER ADJUSTABLE SMD 1101
ZXLD1101ET5TA
功能描述:LED照明驱动器 Series/Parallel RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
ZXLD1320
制造商:DIODES 制造商全称:Diodes Incorporated 功能描述:Buck mode DC-DC converter for LED driving
ZXLD1320DCATC
功能描述:直流/直流开关转换器 DC-DC Buck Conv. 1.5A output RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT
ZXLD1321
制造商:ZETEX 制造商全称:ZETEX 功能描述:Boost mode DC-DC converter for LED driving with 1A output and current control